SPQ2013 Final

This is my preventative maintenance final project; Jeff has required us to pick a vehicle to inspect and document. Down below I have found the factory specifications.

During this portion of class I have learned a lot about the importance of P.M. If the time is not taken to properly care for the vehicle not only is there a shorter vehicle life but possible down time which can cost a lot of money.  

Here is the truck I have chosen
 

 
 
 
 
 
 
 
 
 
 
 

                                                           Here is a brake line leak
 

Here is the cable that is going to snap that holds the hood on

















Lubricating oil specifications
OEM brand: Valvoline Premium Blue or Valvoline Premium Blue Extream
Capacity: 49.2 liters or 13 gallons
Oil filter part number: (Cummins)2882673 or 2882674 (Fleetgaurd) LF9070 or LF9080

MSDS info for Valvoline Premium Blue

http://econtent.autozone.com:24999/znetcs/msds/en/US/689565

*lubricant is vital to wear or contamination and can drastically limit your equipment life. Regular testing should be a part of the PM in any shop.

Coolent specifications
OEM brand: Fleetguard COMPLEATS
Capacity: 26.5 liters or 28qt
Filter part number: fleetguard WF2126^2 or WF2127^3

MSDS info for fleetguard COMPLEATS

http://www.gracepacificcorp.com/PDF/MSDS/Makakilo_Shop/ES%20Compleat%20Coolant%20EG.pdf

*When the coolant gets older it looses its protective properties.  It begins to allow the water to eat up your internal parts.  Water pumps fail, radiators fail and more.  These failures can lead to disastrous engine problems. 

Gear lubes

OEM brand transmission fluid: Road Ranger SAE-50
Cpacity transmission:11.1 liters
Drive axle: Road Ranger EP 75W-90

MSDS road ranger SAE-50

http://www.lubrimaxx.com.au/resource/safetysheet/425.PDF

*Lube oil serves to remove heat from where it’s generated, preventing gearing component temperatures from rising to excessive levels, it also transfers or removes wear particles and any other undesirable contaminants. Failure to lubricate you system WILL result in premature system failure.

Maintenance intervals

General Information

TOC

Automotive Applications Perform maintenance at whichever interval occurs first. At each scheduled maintenance interval, perform all previous maintenance checks that are due for scheduled maintenance. Maintenance Procedures at Daily Interval(1) Air Cleaner Restriction - check Air Intake Piping - check Air Tanks and Reservoirs - drain Coolant Level - check Charge-Air Piping - check Crankcase Breather Tube - check Drive Belts - check Fan, Cooling - check Fuel-Water Separator - drain Lubricating Oil Level - check Aftertreatment Exhaust Piping - check Diesel Exhaust Fluid (DEF) Level - check Maintenance Procedures at 40,000 Kilometers [25,000 Miles], 800 Hours, or 6 Months(1) (3) Pressure Fuel Filter - change Fuel Filter Suction - check Lubricating Oil and Filters - change Radiator Pressure Cap - check Supplemental Coolant Additive (SCA) and Antifreeze Concentration - check Charge-Air Cooler - check Maintenance Procedures at 80,000 Kilometers [50,000 Miles], 1500 Hours, or 1 Year(2) Air Compressor Discharge Lines - check Air Compressor Air Cleaner Element - check Air Leaks, Air Intake and Exhaust Systems - check Cooling Fan Belt Tensioner - check Coolant Filter - change Engine Wiring Harness - check Maintenance Procedures at 200,000 Kilometers [125,000 Miles] or 3000 Hours(5) Crankcase Breather Element - change Maintenance Procedures at 200,000 Kilometers [125,000 Miles], 3000 Hours, or 2 Years Radiator Hoses - check Cold Starting Aid - check Radiator Shutter Assembly - check Vibration Damper, Viscous - check Engine Mounting Bolts - check Engine Steam Cleaning - clean Maintenance Procedures at 241,000 Kilometers [150,000 Miles] or 4500 Hours Aftertreatment Fuel Injector - clean Maintenance Procedures at 320,000 Kilometers [200,000 Miles] or 4500 Hours(4) Aftertreatment Diesel Particulate Filter –  replace or clean Aftertreatment Diesel Exhaust Fluid Dosing Unit Filter - change Maintenance Procedures at 400,000 Kilometers [250,000 Miles], 6000 Hours, or 2 Years Cooling System - flush Maintenance Procedures at 800,000 Kilometers [500,000 Miles], 10,000 Hours, or 5 Years (6) Engine Brake Assembly - test Fan Hub, Belt Driven - check Overhead Set - adjust The lubricating oil and lubricating oil filter intervals are based on Cummins® Engineering Standard 20,081 and a normal duty cycle. Oil change intervals can be adjusted based on fuel consumption and whether or not the oil meets Cummins® Engineering Standard 20,081. See the Oil Drain Intervals Table for Severe Duty and Light Duty drain intervals in this section. Follow the manufacturer's recommended maintenance procedures for the starter, alternator, generator, batteries, electrical components, engine brakes, exhaust brake, charge-air cooler, air compressor, air conditioner compressor, and fan clutch. Test the SCA concentration level every 6 months unless the concentration is over three units; then check at every oil drain interval until the concentration is below three units. Use the following procedure for coolant condemnation limits. Refer to Procedure 018-004 in Section V. The aftertreatment diesel particulate filter intervals can be adjusted, based on the type of engine oil that is used. See the Aftertreatment Cleaning Intervals table for cleaning intervals. While air cleaning is allowed, the Cummins Inc. preferred method would be to exchange the DPF at the recommended maintenance interval. The crankcase breather element intervals can be adjusted, based on engine blowby. See the Crankcase Breather Element Change Intervals table below. The components of the engine brake that are subjected to wear during normal operation of the engine are available as a kit through Cummins® Inc. Distributors/Dealers. It is recommended to do this maintenance at 800,000 km [500,000 mi], 10,000 hours, or 5 years. All EPA 07, EPA 10, EPA Tier 4 Interim/European Union Stage IIIB 2011(174 -751 hp) engine systems equipped with exhaust aftertreatment must operate on ultra-low sulfur diesel (ULSD) with a maximum sulfur content of 15 ppm in the United States and 10 ppm in the European Union. Failure to do so can permanently damage engine and aftertreatment systems within a short period of time. This damage could cause the engine to become inoperable and affect the warranty coverage on the engine system. Aftertreatment Cleaning Intervals Oil Classification Kilometers/miles Hours CES20081 320,000 [200,000] 4500 CES20078 241,000 [150,000] 4500 Crankcase Breather Element Change Intervals Engine Blowby Interval Less than 305 mm-H2O [12 in-H2O] 200,000 km [125,000 mi] or 3,000 hr Greater than or equal to 305 mm-H2O [12 in-H2O] 120,000 km [75,000 mi] or 1,500 hr

Also I found 49 zerk fittings on the Peterbilt here are some pictures of the ones I almost missed.




Hours This Week: 25
Hours Total: 298